Anchor Bolt Suppliers in KSA | Anchor Fasteners, Manufacturers & Dealers in Saudi Arabia

Wolouf Industries Factory — Through Bolt and Sleeve Anchor Supplier, Dammam KSA

DAMMAM · Coastal Road · Through Bolt & Sleeve Anchor Manufacturer

Address: Coastal Road, Dammam, KSA  |  Phone: +966 13 818 9441

Products They Offer

• SPIT Through Bolt Anchor 55 mm — a carbon steel through-fixing bolt engineered for non-cracked concrete, sized M8 diameter by 55mm length. The SPIT Fix3 system is a hammer-set through bolt: the anchor is dropped into a pre-drilled hole, the fixture is positioned over it, and the bolt is set with repeated hammer strikes rather than a torque wrench, which makes it fast to install in high volume on repetitive fixing patterns like formwork ties, conduit clips, and light equipment brackets.
• Sleeve Anchor Bolt 10×80 mm — a mechanical expansion anchor where a threaded stud sits inside a full-length expanding metal sleeve. As the nut is tightened, the sleeve is drawn up and expands radially against the drilled hole wall along its entire length, rather than at a single point like a wedge anchor - this gives even load distribution and makes the sleeve anchor a reliable choice for fixtures where the load direction may vary, such as railings and handrail posts.
• Through Bolt — a general-purpose through-fixing bolt used with a nut and washer on the reverse face of the material being fixed, correct wherever both sides of the fixed component are accessible during installation and a mechanical expansion anchor isn't needed.

Why Choose Wolouf Industries Factory

Wolouf Industries Factory operates as a manufacturing facility on Dammam's Coastal Road, positioning it directly for the Eastern Province's dense concentration of industrial, petrochemical, and marine construction projects around Dammam, Khobar, and the Jubail industrial corridor. As a factory rather than a pure trading house, Wolouf is positioned to supply through bolts and sleeve anchors in the higher volumes that repetitive fixing patterns on large industrial projects typically require, and to take custom length or diameter requests that a reseller carrying only pre-packaged retail stock generally can't accommodate.

• Delivery coverage: Dammam and the wider Eastern Province, with the Coastal Road location giving practical access to Khobar, Dhahran, and Jubail industrial sites
• Product focus: Through bolts and sleeve anchors specifically, rather than a broad general fastener catalogue
• Confirm before ordering: Ask directly about current lead times and minimum order quantities for custom lengths, since manufacturing capacity and stock availability change - this guide reflects the product range, not live inventory

Metal Fasteners Mfr. Co. Ltd — Stainless Steel, Duplex, Nickel and Hastelloy Anchor Bolt Manufacturer, Dammam KSA

DAMMAM · King Saud Street · Manufacturer · Exotic Alloy & Stainless Grades

Address: King Saud Street, Dammam 31432, KSA  |  Phone: +966 13 817 5905

Products They Offer

• SS 304 / SS 316 / SS 310S Stainless Steel Anchor Bolts — manufactured to ASTM/ASME SA 312 grade requirements across TP304, 304L, 304H, 309S, 309H, 310S, 310H, 316, 316TI, 316H, 316LN, 317, 317L, 321, 321H, 347, 347H, and 904L. SS304 covers general atmospheric corrosion resistance for most indoor and dry-climate fixings; SS316 adds molybdenum for better resistance to chlorides, making it the standard specification for coastal Jeddah and Dammam exposure or any application near seawater or de-icing salts; SS310S adds high-temperature oxidation resistance for anchors installed near furnaces, ovens, or other elevated-temperature process equipment.
• Duplex Steel Anchor Bolts — UNS S31803, S32205, S32550, S32750, and S32760 grades. Duplex stainless combines a ferritic-austenitic microstructure that gives roughly double the yield strength of standard austenitic stainless (304/316) alongside superior resistance to chloride stress-corrosion cracking, which is why it's specified over standard stainless for offshore platforms, desalination plants, and aggressive marine splash-zone anchoring.
• ASTM F467 Monel Anchor Bolts — nickel-copper alloy grades 200 and 201, supplied to the ASTM F467 nut standard commonly paired with Monel bolting. Monel resists corrosion from seawater, hydrofluoric acid, and many reducing acid environments better than stainless steel, and is specified where the anchor will see direct chemical process exposure rather than just atmospheric corrosion.
• Hastelloy Anchor Bolts — Hastelloy C-22, C-276, and C-2000 nickel-molybdenum-chromium alloy grades, used where the anchor faces a combination of oxidizing and reducing chemical exposure that would attack both standard stainless and Monel - the top tier of corrosion-resistant alloy specification for chemical processing and flue-gas desulfurization environments.

Why Choose Metal Fasteners Mfr. Co. Ltd

Metal Fasteners Mfr. Co. Ltd is the only supplier in this guide manufacturing the full stainless, duplex, nickel alloy, and Hastelloy range from a Dammam base on King Saud Street, placing it inside the Eastern Province's petrochemical and industrial manufacturing zone where these exotic-alloy grades are most in demand. Buying an alloy-grade anchor bolt direct from a manufacturer rather than a general trading house matters specifically because these grades usually require material certification (mill test certificates) tracing the alloy composition back to the melt - a manufacturer is positioned to provide that documentation directly, which shortens the paper trail contractors need for QA/QC sign-off on petrochemical and marine projects.

• Delivery coverage: Dammam and the Eastern Province petrochemical corridor, including Jubail and Ras Tanura-adjacent industrial sites
• Product focus: The broadest alloy grade range in this guide - stainless (SS304/316/310S), duplex, Monel, and Hastelloy - rather than standard carbon steel
• Ask directly about: Current mill test certificate and material traceability documentation for the specific grade and heat/batch being ordered, since certification requirements vary by project and client

Brooq Al Amaan Trading — L-Type and J-Type Anchor Bolt Supplier, Dammam KSA

DAMMAM · Prince Mansur Street · L Type, J Type & Threaded Rod Anchors

Address: Building No. 5582, Al Bassam Tower 9th Floor, Office No. 901, Prince Mansur Street, Dammam, KSA  |  Phone: +966 13 814 0866

Products They Offer

• Anchor Bolt 1 to 4 Inch — foundation bolts with UNC, 8UN, UNF, and Metric coarse/fine thread options, manufactured to ASTM, ASME, BS, DIN, and BS EN ISO standards, available with bend angles of 90°, 120°, or 135° and nominal diameters from 1 to 4 inches. The bend angle matters because it determines the anchor's pull-out resistance once cast into concrete - a 90° L-bend is the most common, while a 135° hook is specified where the structural design calls for greater resistance to tension pull-out in a shallower embedment depth.
• L Anchor Bolts 0.25 to 1.25 in — available in A36, A193-B7, SS304, and SS316 grades with a choice of black, electro galvanized, yellow, hot-dip galvanized, or PTFE coating, in both metric and imperial sizing. A36 covers standard structural applications; A193-B7 is a higher-strength alloy steel grade for higher-load structural steel column base connections; the coating choice should track the exposure environment - hot-dip galvanized for outdoor and coastal installations, PTFE where chemical resistance or reduced friction during installation matters.
• J Bolt — sizes 0.25 to 4 inches, with finishes spanning self (bare), black oxide, electro galvanized, zinc bi-chromate yellow, hot-dip galvanized, and PTFE, manufactured to DIN, ASTM, AISI, BS, JIS, UNS, EN, ISO, SAE, and ASME standards. The J-hook embedded end resists pull-out under tension more effectively than a straight rod of equal diameter, which is why J bolts are specified over straight anchor rods on higher-tension foundation connections.

Why Choose Brooq Al Amaan Trading

Brooq Al Amaan Trading operates from Al Bassam Tower on Prince Mansur Street in Dammam, a central commercial address giving straightforward access for contractors and procurement teams working Eastern Province structural steel and foundation projects. Its product range is weighted specifically toward the cast-in-place foundation bolt category - L type, J type, and the widest quoted thread-standard spread in this guide (nine separate standards for the J bolt line alone) - which matters on projects where the structural engineer's drawing specifies a standard the contractor's usual supplier doesn't stock.

• Delivery coverage: Dammam and Eastern Province structural and industrial construction sites
• Product focus: Cast-in-place foundation anchors (L type, J type) across an unusually wide range of grades, coatings, and international thread standards
• Ask directly about: Confirming the exact standard (ASTM, DIN, BS, or JIS) called for on the structural drawing before ordering, since Brooq's range spans multiple standards that aren't interchangeable

Steel Corner Trading Est — Wedge Anchor and Shield Anchor Supplier, Riyadh KSA

RIYADH · Old Industry · Wedge Anchor & Shield Anchor Stockist

Address: Old Industry, Al Madina Almunwarah Road, Riyadh, KSA  |  Phone: +966 54 350 0097  |  Mobile: +966 55 173 5059

Products They Offer

• Wedge Anchor 6 mm — a torque-controlled expansion anchor, 6mm diameter, 45mm to 100mm length range. Installation involves drilling a hole matched exactly to the anchor's rated diameter, driving the anchor to the marked embedment depth, then tightening the nut to the manufacturer's specified installation torque - undertightening leaves the expansion clip's radial preload incomplete and can cut pull-out capacity significantly, while overtightening with an impact gun risks crushing the surrounding concrete. A properly set wedge anchor is rated for both cracked and non-cracked concrete, which is why it's the general-purpose default across most Saudi concrete fixing work.
• Stainless Steel Wedge Anchor 8 mm — 8mm diameter, 80mm to 100mm length range, in stainless steel construction. Correct wherever the carbon-steel equivalent's coating would eventually corrode - exterior, coastal, or washdown environments - since the corrosion resistance runs through the full cross-section rather than sitting on the surface as a plated finish.
• Shield Anchor with Eye Open Hook, 6 mm — a split-shell expansion anchor, 6mm diameter, 40mm to 80mm length range, fitted with an open eye hook rather than a bolt head. The shell expands as a screw or bolt is driven into it, and the open eye hook lets a chain, cable, or suspension fixture be attached directly - a common choice for suspended conduit runs, cable trays, and light fixtures where the load hangs below the fixing point.

Why Choose Steel Corner Trading Est

Steel Corner Trading Est is based in Riyadh's Old Industry district on Al Madina Almunwarah Road, an established industrial supply zone giving it straightforward reach across the capital's construction and maintenance sector. The company publishes both a landline and mobile contact number, giving buyers a direct route for urgent site orders outside normal office hours, which matters on active construction sites where a fixing shortfall can halt a crew. Its product range concentrates specifically on the two anchor types most commonly specified for general concrete and suspended fixing work - wedge anchors and shield anchors - in both standard and stainless steel grades, rather than spreading thin across every anchor category.

• Delivery coverage: Riyadh and the Central Region
• Product focus: Wedge anchors and shield anchors, standard and stainless steel
• Two contact routes: Landline and mobile both published, useful for urgent same-day or next-day site orders

Muhammad Omar Al Attas Trading Store — Zinc-Plated Through Bolt and White Steel Anchor Supplier, Riyadh KSA

RIYADH · Industrial District · Zinc-Plated & Frame Anchor Bolts

Address: Al Qatadiya Street, Industrial District, Riyadh, KSA  |  Phone: +966 11 448 5715  |  Mobile: +966 50 061 5557

Products They Offer

• Zinc Plated Through Bolt 10×100 mm — branded TUF FIX, white finish, carbon steel construction, 10mm diameter by 100mm length. Zinc plating gives a light, cosmetically clean corrosion barrier suited to dry interior fixing work and general finishing applications where a heavy hot-dip galvanized coating's thicker, rougher finish isn't wanted.
• Anchor Bolt Without Sleeve, White Steel — branded BEAM, white color, zinc-plated finish, 55mm length, 6mm diameter, steel construction. A sleeveless design means the bolt itself makes direct contact with the drilled hole rather than through an intermediate expansion sleeve, generally a lighter-duty option suited to fixtures and fittings rather than structural or heavy-load applications.
• GI Metal Frame Anchor — a galvanized-iron frame anchor built specifically for securing door, window, and structural frames into surrounding masonry or concrete, where the anchor needs to sit flush within the frame profile rather than project as a standard bolt head.

Why Choose Muhammad Omar Al Attas Trading Store

Muhammad Omar Al Attas Trading Store operates from Al Qatadiya Street in Riyadh's Industrial District, an area concentrated with general construction and fit-out suppliers, positioning it well for finishing contractors and joinery/window installers sourcing frame and light fixing hardware. The store carries branded product lines specifically - TUF FIX zinc-plated through bolts and BEAM white steel anchors - rather than only unbranded generic stock, which gives buyers a recognisable name on the delivery note and a consistent specification to reorder against on repeat projects.

• Delivery coverage: Riyadh Industrial District and the wider Central Region
• Product focus: Branded zinc-plated through bolts and frame anchors for finishing and general construction work
• Two contact routes: Landline and mobile both published

Bolt Castle Trading EST. — Lindibolt, Straight Type and Self Anchor Bolt Supplier, Riyadh KSA

RIYADH · Al Awaidah Industrial City · Specialty & Branded Anchor Bolts

Address: Al Awaidah Industrial City, Abu Umamah Al Ansari Street, Riyadh, KSA  |  Phone: +966 53 929 5525  |  Mobile: +966 55 731 2909

Products They Offer

• Lindibolt Type LB2 — M10 size, 74mm length, rated to a 6 Nm tightening torque. Lindibolt is a specialty rivet-and-anchor system originally developed for machine and equipment mounting, where the low, precisely specified tightening torque matters for repeatable, vibration-resistant clamp load on rotating or vibrating machinery bases.
• Anchor Bolt Straight Type (ASTM A36/36M) — Grade GR-A, Model TY-S, straight-type configuration manufactured to ASTM A36/36M. A straight anchor rod cast into fresh concrete, typically fitted with a plate or nut at the embedded end for pull-out resistance, used on engineered structural steel column base connections where the anchor bolt pattern and embedment depth are set by the structural drawing.
• Self Anchor Bolt 60×8 mm (0.01 kg) — available in 60×8, 60×10, 70×10, 80×10, 80×12, and 100×12mm sizes, each a compact self-drilling or self-tapping design that reduces the installation to a single drilling and driving step rather than a separate drill-then-anchor sequence.
• Fischer FAZ II Classic Bolt Anchor — the international Fischer FAZ II bolt anchor range, a torque-controlled wedge anchor approved for both cracked and non-cracked concrete from roughly C20/25 up to C50/60 strength class. The FAZ II sets with a conical bolt that's pulled into an expansion clip as the installation torque is reached, giving high load capacity with fewer fixing points - commonly specified for railings, steel structures, stairs, and cable tray fixings where a documented international approval is required on the specification.

Why Choose Bolt Castle Trading EST.

Bolt Castle Trading EST. operates from Al Awaidah Industrial City in Riyadh, an industrial zone that gives it good positioning for machinery, plant, and structural steel contractors across the capital. What sets Bolt Castle apart in this guide is its stock of internationally-branded specialty anchor systems - Lindibolt and Fischer FAZ II - alongside standard straight-type and self-drilling anchors, meaning buyers who specifically need a documented, internationally-approved anchor system (rather than an unbranded equivalent) have a named supplier to call rather than needing to source through an international distributor directly.

• Delivery coverage: Riyadh and Al Awaidah Industrial City surrounds
• Product focus: Internationally-branded specialty anchor systems (Lindibolt, Fischer) alongside straight-type and self-drilling anchors
• Two contact routes: Landline and mobile both published

Sleeve Anchor Bolts - Mechanical Expansion Anchors for Concrete Fixing

• •Construction: A threaded stud inside an expanding metal sleeve, drawn tight against the drilled hole wall as the nut is tightened
• •Why it suits: Correct for solid, non-cracked concrete where the sleeve's full-length contact gives reliable holding without the concrete needing to be pre-drilled to a special profile
• •Price: SAR 3-25 per piece  |  Where to buy: Wolouf Industries Factory

Wedge Anchor Bolts - Heavy Duty Concrete Anchor Bolts for Cracked and Non-Cracked Concrete

• •Construction: A tapered clip at the embedded end that wedges outward against the drilled hole as the bolt is set - 6mm to 25mm+ diameter range, carbon or stainless steel
• •Why it suits: The most widely specified heavy duty concrete anchor bolt because it's rated for both cracked and non-cracked concrete - the safer default where the concrete condition isn't fully documented
• •Price: SAR 4-40 per piece (carbon steel), SAR 12-70 (stainless)  |  Where to buy: Steel Corner Trading Est

Thru Bolt / Through Bolt Anchor - Full-Diameter Fixings for General Construction

• •Construction: A full-length bolt passing completely through the fixed material, secured with a nut and washer on the far face - carbon steel, zinc-plated finish common
• •Why it suits: Correct wherever access to both sides of the fixed material is possible, giving a mechanically simpler and often more cost-effective fixing than a blind anchor
• •Price: SAR 5-35 per piece  |  Where to buy: Wolouf Industries Factory, Muhammad Omar Al Attas Trading Store

L Type Anchor Bolt - Foundation Anchoring for Structural Base Plates

• •Construction: A rod bent to a 90° L-shape and cast into fresh concrete, with the threaded straight leg projecting for the fixed component - 0.25 to 1.25 inch diameter range common
• •Why it suits: Correct for foundation bolt applications set into wet concrete before the structure is poured, rather than drilled into cured concrete like a mechanical anchor
• •Price: SAR 8-60 per piece, grade and coating dependent  |  Where to buy: Brooq Al Amaan Trading

J Type Anchor Bolt - Hooked Foundation Bolts for Cast-In-Place Concrete

• •Construction: A rod bent into a J-hook shape at the embedded end, 0.25 to 4 inch size range, cast into concrete before it cures
• •Why it suits: The J-hook shape resists pull-out under tension better than a straight embedded rod of the same diameter, correct for higher-load foundation anchoring
• •Price: SAR 10-70 per piece  |  Where to buy: Brooq Al Amaan Trading

Straight Anchor - Cast-In Foundation Bolts for Structural Steel Baseplates

• •Construction: A straight threaded rod cast directly into concrete, typically fitted with an anchor plate or nut at the embedded end for pull-out resistance - ASTM A36/36M grade GR-A common
• •Why it suits: Correct for engineered structural steel column base connections where the anchor bolt pattern and embedment depth are set by the structural design, not adjusted on site. Price: SAR 15-90 per piece  |  Where to buy: Bolt Castle Trading EST.

Shield Anchor - Expansion Shell Anchors for Light to Medium Fixings

• •Construction: A split metal shell that expands as a lag screw or bolt is driven in, 6mm to 16mm diameter range, available with an open eye hook for suspended fixtures
• •Why it suits: Correct for lighter fixtures - cable trays, conduit hangers, light fittings - where a full wedge or sleeve anchor's capacity would be unnecessary. Price: SAR 3-20 per piece  |  Where to buy: Steel Corner Trading Est

Rock Bolts and Self-Drilling Anchors for Ground and Rock Anchoring

• •Construction: A high-tensile threaded bar grouted or mechanically anchored into drilled rock or ground, used in slope stabilization and tunnel support applications
• •Why it suits: Correct for geotechnical applications - road cuttings, retaining structures, mine or tunnel support - distinct from standard concrete fixing anchors. Price: Project-specific, request a quotation

Thru Bolt / Wedge Anchor Bolt Supplier In Saudi Arabia

Wolouf Industries Factory covers thru bolt (through bolt) stock, while Steel Corner Trading Est covers wedge anchor bolts in both carbon and stainless steel - the two most commonly specified concrete-fixing anchor types on general construction sites.

Concrete Anchor Bolts Suppliers Saudi Arabia

Sleeve, wedge, and shield anchor bolts for concrete fixing are stocked by Wolouf Industries Factory and Steel Corner Trading Est - see the Types of Anchor Bolts section above for the full concrete-fixing range and which product suits cracked versus non-cracked concrete.

Anchor Bolt Supplier & Exporter in Saudi Arabia

Metal Fasteners Mfr. Co. Ltd manufactures and stocks certified stainless, duplex, Monel, and Hastelloy grades suited to both domestic Saudi projects and export-grade specifications requiring documented material traceability.

Hex Nut Supplier in Saudi Arabia

Most anchor bolt suppliers covered in this guide also stock matching hex nuts and washers as part of a complete fixing set - confirm hex nut grade and thread pitch match the anchor bolt's own grade and thread when ordering, rather than assuming a standard hex nut fits any bolt of the same nominal diameter.

SPIT Through Bolt Anchor 55 mm for Non-Cracked Concrete Fixing

The SPIT Fix3 through bolt anchor is a hammer-set expansion anchor built from carbon steel, designed specifically for solid, non-cracked concrete. It's inserted into a pre-drilled hole matched to its M8 diameter and set with repeated hammer strikes rather than a torque wrench, which is what makes it fast to install across repetitive fixing patterns - formwork ties, conduit clips, cable tray brackets, and light equipment mounts - where dozens or hundreds of identical fixings are needed on the same job. Because it's rated for non-cracked concrete only, it should not be substituted onto a structural element where flexural cracking under service load is possible; a wedge anchor is the correct substitute in that case.

Material: Carbon Steel | Application: Non-cracked concrete | Anchor Length: 55 mm | Anchor Diameter: M8

Price: SAR 6-12  |  Where to buy: Wolouf Industries Factory

Anchor Bolt 1 to 4 Inch for Structural Steel Foundation Bolting

A foundation anchor bolt range spanning 1 to 4 inches nominal diameter, offered in UNC, 8UN, UNF, and Metric coarse or fine thread series, manufactured to ASTM, ASME, BS, DIN, or BS EN ISO standards depending on which the project specification calls for. The bend angle - 90°, 120°, or 135° - is not a cosmetic choice: a sharper bend angle increases the anchor's resistance to being pulled straight out of the concrete under tension load, so structural engineers specify the bend angle based on the calculated uplift force on the connection, not on convenience. This is the size range most commonly specified for column base plates, crane rail foundations, and heavy machinery bases.

Thread: UNC, 8UN, UNF, Metric Coarse & Fine Series | Standard: ASTM / ASME / BS / DIN / BS EN ISO | Bend Angle: 90°, 120°, 135° | Nominal Diameter: 1-4 in

Price: SAR 30-180, size dependent  |  Where to buy: Brooq Al Amaan Trading

Lindibolt Type LB2 for Precision Machine and Equipment Mounting

The Lindibolt LB2 is a specialty M10 anchor system originally developed for machine and equipment base mounting, where a precisely repeatable clamp load matters more than raw pull-out strength. Rated to a 6 Nm tightening torque - low compared to a standard structural wedge anchor - it's designed to be set consistently by hand or with a low-torque tool across many identical fixing points on a machine bed or equipment frame, reducing the risk of overtightening damaging a precision-aligned base. At 74mm length, it suits shallow-embedment equipment mounting rather than deep structural foundation work.

Size: M10 | Type: LB2 | Length: 74 mm | Tightening Torque: 6 Nm

Price: SAR 8-18  |  Where to buy: Bolt Castle Trading EST.

Anchor Bolt Straight Type (ASTM A36/36M) for Structural Steel Column Base Plates

A straight-type anchor bolt manufactured to ASTM A36/36M, Grade GR-A, Model TY-S - a straight threaded rod cast directly into fresh concrete rather than drilled into cured concrete like a mechanical anchor. Straight anchors are typically fitted with an anchor plate or nut at the embedded end to resist pull-out, and are the standard choice for engineered structural steel base connections where the anchor bolt pattern, embedment depth, and projection length above the concrete are fixed by the structural drawing rather than adjusted on site. ASTM A36 is a general-purpose structural steel grade widely referenced on Saudi structural drawings for standard-load column bases.

Type: Straight Type | Grade: GR-A | Model: TY-S | Standard: ASTM A36/36M

Price: SAR 20-95, length dependent  |  Where to buy: Bolt Castle Trading EST.

Anchor Bolt Without Sleeve, White Steel for Light Fixture and Fitting Installation

Branded BEAM, this sleeveless anchor bolt makes direct contact between the bolt body and the drilled hole rather than through an intermediate expanding sleeve, at 6mm diameter and 55mm length with a white zinc-plated finish. The sleeveless design is generally a lighter-duty option than a sleeve or wedge anchor, correct for shelving brackets, light fixtures, and interior fittings rather than structural loads, and the zinc-plated white finish is a cosmetic and light-corrosion-protection choice suited to visible interior installations.

Brand: BEAM | Color: White | Finish: Zinc Plated | Length: 55 mm | Diameter: 6 mm | Material: Steel

Price: SAR 4-9  |  Where to buy: Muhammad Omar Al Attas Trading Store

L Bolts SS 12m for Long-Span Foundation and Structural Steel Anchoring

An L-shaped foundation bolt line running from 200mm up to 500mm length at a 12mm nominal size, cast into fresh concrete before the pour cures. The longer end of this length range is specified where the structural design calls for deeper embedment to develop higher pull-out and shear capacity - typical on heavier column bases and equipment foundations where a short L bolt wouldn't achieve the required anchorage depth in the available concrete section.

Size: 12 mm | Maximum Length: 500 mm | Minimum Length: 200 mm

Price: SAR 18-65  |  Where to buy: Brooq Al Amaan Trading

L Anchor Bolts 0.25 to 1.25 in for Multi-Grade Structural Foundation Work

This L anchor bolt range covers four material grades - A36 for standard structural work, A193-B7 for higher-strength alloy steel applications, and SS304/SS316 for corrosion-exposed installations - across a 0.25 to 1.25 inch diameter range in both metric and imperial sizing. The coating choice (black, electro galvanized, yellow, hot-dip galvanized, or PTFE) should be matched to the exposure: hot-dip galvanized for exterior and coastal work where the anchor will see decades of weathering, PTFE where chemical resistance or reduced friction on installation matters, and standard black or yellow finishes for dry interior applications where cost is the priority.

Grade: A36, A193-B7, SS304, SS316 | Coating: Black, Electro Galvanized, Yellow, Hot Dip Galvanized, PTFE | Standard: Metric and Imperial Size | Diameter Range: 0.25-1.25 in

Price: SAR 12-85, grade dependent  |  Where to buy: Brooq Al Amaan Trading

J Bolt for High-Tension Foundation and Anchor Bolt Applications

A J-shaped foundation bolt covering 0.25 to 4 inch sizes, offered in self (bare), black oxide, electro galvanized, zinc bi-chromate yellow, hot-dip galvanized, and PTFE finishes, manufactured to nine referenced standards (DIN, ASTM, AISI, BS, JIS, UNS, EN, ISO, SAE, ASME). The J-hook shape at the embedded end resists pull-out under tension more effectively than a straight rod of the same diameter, because the hook mechanically engages the surrounding concrete rather than relying on bond strength alone - this is why J bolts are specified over straight anchor rods wherever the connection sees significant uplift or tension load.

Size: 0.25-4 in | Finish: Self, Black Oxide, Electro Galvanized, Zinc Bi-Chromate Yellow, Hot Dip Galvanized, PTFE | Standard: DIN, ASTM, AISI, BS, JIS, UNS & EN, ISO, SAE, ASME | Threading: UNC, 8UN, BSW, UNF, BSF

Price: SAR 10-70, size dependent  |  Where to buy: Brooq Al Amaan Trading

Self Anchor Bolt 60×8 mm for Fast Single-Step Fixing Installation

A compact self-drilling anchor bolt line available in six size combinations - 60×8, 60×10, 70×10, 80×10, 80×12, and 100×12mm - each engineered to reduce installation to a single drilling-and-driving step rather than the usual drill-hole-then-insert-anchor sequence. At 0.01 kg per unit, these are lightweight fixings suited to fast-turnaround jobs like fixing brackets, light equipment, and cable management where the labour time saved on installation matters as much as the fixing itself.

Sizes: 60×8, 60×10, 70×10, 80×10, 80×12, 100×12 mm | Weight: 0.01 kg

Price: SAR 2-6  |  Where to buy: Bolt Castle Trading EST.

Shield Anchor with Eye Open Hook, 6 mm for Suspended Cable and Conduit Fixing

A split-shell expansion anchor at 6mm diameter, 40mm to 80mm length range, fitted with an open eye hook rather than a standard bolt head. The metal shell expands radially as a screw or lag bolt is driven through the anchor's centre, and the open eye hook lets a chain, wire rope, or suspension bracket be attached directly to the anchored point - the standard fixing for suspended cable trays, conduit hangers, and light fittings hanging below a ceiling or structural soffit rather than mounted flush to a surface.

Type: Shield Anchor | Size Diameter: 6 mm | Maximum Length: 80 mm | Minimum Length: 40 mm

Price: SAR 4-11  |  Where to buy: Steel Corner Trading Est

Zinc Plated Through Bolt 10×100 mm for General Construction and Finishing Work

A carbon steel through-fixing bolt from the TUF FIX brand, 10mm diameter by 100mm length, finished in white zinc plating. Zinc plating gives a light, cosmetically clean corrosion barrier that suits dry interior fixing work and general finishing applications, where the thicker, rougher texture of a hot-dip galvanized coating isn't wanted on a visible fixing. As a through bolt, it needs access to both sides of the fixed material for the nut and washer, distinguishing it from a blind mechanical anchor that only needs access from one face.

Size: 10×100 mm | Brand: TUF FIX | Color: White | Material: Carbon Steel

Price: SAR 5-12  |  Where to buy: Muhammad Omar Al Attas Trading Store

Sleeve Anchor Bolt 10×80 mm for Standard Concrete Fixing

A mechanical expansion anchor at 10mm diameter, 80mm length - a threaded stud inside a full-length expanding metal sleeve that's drawn tight against the drilled hole wall as the nut is tightened. The sleeve's full-length contact gives even load distribution along its embedded length, correct for solid non-cracked concrete fixings where the load direction may vary, such as railings, handrail posts, and general equipment mounting.

Price: SAR 5-14  |  Where to buy: Wolouf Industries Factory

Sleeve Anchor Bolt Type for General Concrete Fixing Applications

The general sleeve anchor bolt product line - stocked across multiple diameters and lengths for standard non-cracked concrete fixing work. As a category, sleeve anchors sit between the compact wedge anchor and the heavier through bolt in terms of application: quick to install, rated for moderate-to-heavy loads, and correct wherever the fixing point sees load from more than one direction.

Price: SAR 4-30, size dependent  |  Where to buy: Wolouf Industries Factory

Bolt Anchor With Plate for Wide-Area Load Distribution

An anchor bolt fitted with a base plate at the embedded end rather than a plain rod, spreading the pull-out load over a larger bearing area within the concrete. This is the correct choice where calculated tension load is too high for a standard hook or bend to resist reliably in the available embedment depth - the plate mechanically locks against the surrounding concrete mass rather than relying on hook geometry or bond strength alone.

Price: SAR 25-110, plate size dependent  |  Where to buy: Brooq Al Amaan Trading

Concrete Anchor Steel for General-Purpose Structural and Site Fixing

A general carbon steel concrete anchor line covering everyday structural and site fixing needs where the application doesn't call for a specialty type, coating, or alloy grade - the default, cost-effective specification for indoor and inland construction work in Riyadh where corrosion exposure isn't a primary concern.

Price: SAR 3-25, size dependent  |  Where to buy: Wolouf Industries Factory

Anchor Bolt Grade 4.8 L Type, White Color for Standard-Load Foundation Bolting

An L-type foundation anchor bolt in property class Grade 4.8 - a mild-strength carbon steel grade suited to standard-load structural connections rather than high-tensile applications - finished in a white coating for a clean, corrosion-protected appearance where the bolt remains visible after installation. Grade 4.8 is a common default specification on general commercial and light industrial foundation work across Saudi Arabia where the structural load doesn't demand a higher-strength grade like A193-B7.

Price: SAR 10-55, length dependent  |  Where to buy: Brooq Al Amaan Trading

Monel Anchor Bolt for Marine and Chemical Process Exposure

A nickel-copper Monel alloy anchor bolt, typically supplied to the ASTM F467 nut standard. Monel resists corrosion from seawater, hydrofluoric acid, and many reducing-acid environments more effectively than standard stainless steel, which is why it's specified for anchors facing direct chemical process exposure - offshore platforms, desalination equipment, and process piping supports - rather than just general atmospheric or coastal corrosion, where stainless steel is usually sufficient and considerably less expensive.

Price: SAR 45-220, size dependent  |  Where to buy: Metal Fasteners Mfr. Co. Ltd

Fischer FAZ II Classic Bolt Anchor for Certified Heavy-Load Steel and Railing Fixings

The Fischer FAZ II is a torque-controlled wedge anchor with ETA and ICC approval, rated for use in both cracked and uncracked concrete from roughly C20/25 up to C50/60 strength class. Installation is straightforward - the hole is cleaned of drilling dust, the anchor is hammered in with a few strokes, and the nut is tightened to the specified torque, at which point the expansion clip anchors itself into the concrete and carries load particularly securely into the base material. It's commonly specified for railings, steel structures, stairs, and cable tray fixings on projects where the specification calls for a documented, internationally-approved anchor system rather than an unbranded equivalent.

Price: SAR 15-75, size dependent  |  Where to buy: Bolt Castle Trading EST.

Through Bolt for Full-Access Mechanical Fixing

A general through-fixing bolt passing completely through the material being fixed and secured with a nut and washer on the reverse face - the correct choice wherever both sides of the fixed component are accessible during installation. Through bolts are mechanically simpler than blind mechanical anchors and often more cost-effective, since they don't rely on an expansion mechanism to develop holding capacity.

Price: SAR 4-30, size dependent  |  Where to buy: Wolouf Industries Factory

GI Metal Frame Anchor for Door, Window and Frame Fixing

A galvanized-iron anchor built specifically for securing door, window, and structural frames into surrounding masonry or concrete, designed to sit flush within the frame profile rather than project as a standard bolt head. The galvanized coating gives corrosion protection appropriate to frame installations that may sit against masonry with residual construction moisture, common in Saudi finishing and joinery work.

Price: SAR 4-15, size dependent  |  Where to buy: Muhammad Omar Al Attas Trading Store

Hook Anchor Bolt for Suspended and Hanging Fixtures

An anchor bolt fitted with a hook rather than a standard nut-and-thread head, letting a cable, chain, or suspension bracket attach directly to the anchored point without an additional eyebolt or fitting. Correct for suspended conduit, light fixtures, or cable runs hanging below a ceiling or structural soffit, where the load direction is primarily downward tension rather than shear.

Price: SAR 5-20, size dependent  |  Where to buy: Steel Corner Trading Est

Shield Anchor 6 to 16 mm for Light to Medium-Duty Concrete Fixing

The full shield anchor diameter range, 6mm through 16mm, covering light fixtures at the small end up to medium-duty structural brackets and equipment mounts at the larger sizes. As diameter increases through this range, so does the shield anchor's holding capacity and the fixture types it's suited to - always match the diameter to the calculated or manufacturer-rated load for the specific fixture, not just the nearest available size.

Price: SAR 3-35, diameter dependent  |  Where to buy: Steel Corner Trading Est

Wedge Anchor 6 mm for Cracked and Non-Cracked Concrete Fixing

A torque-controlled wedge expansion anchor, 6mm diameter, 45mm to 100mm length range. The anchor's tapered clip at the embedded end wedges outward against the drilled hole wall as the nut is tightened to a manufacturer-specified installation torque - too little torque and the clip never reaches full radial preload, cutting holding capacity; too much torque, especially with an impact driver, risks crushing the surrounding concrete and losing preload over time. A wedge anchor set correctly is rated for both cracked and non-cracked concrete, which is why it's the safest general-purpose default anchor type where the concrete condition isn't fully documented on the drawing.

Diameter: 6 mm | Maximum Length: 100 mm | Minimum Length: 45 mm

Price: SAR 4-10  |  Where to buy: Steel Corner Trading Est

Stainless Steel Wedge Anchor 8 mm for Corrosive and Coastal Environments

The same torque-controlled wedge expansion mechanism as the standard carbon-steel wedge anchor, built entirely in stainless steel at 8mm diameter with an 80mm to 100mm length range. Because the corrosion resistance runs through the full cross-section of the metal rather than sitting on the surface as a plated coating, this variant holds up in exterior, coastal Jeddah or Dammam, and washdown environments where a carbon-steel equivalent's zinc or galvanized coating would eventually wear through and expose bare steel to corrosion.

Diameter: 8 mm | Material: Stainless Steel | Maximum Length: 100 mm | Minimum Length: 80 mm

Price: SAR 12-28  |  Where to buy: Steel Corner Trading Est

Nut Type Sleeve Anchor for Low-Profile Concrete Fixing

A sleeve anchor built with a nut-style head rather than a bolt head, giving a lower installed profile than a standard bolt-head sleeve anchor and letting the fixed component be tightened directly onto the anchor's protruding thread. Like all sleeve anchors, it works by expanding a full-length metal sleeve radially against the drilled hole wall as the nut is tightened, giving even load distribution along the anchor's embedded length rather than concentrated at a single point.

Price: SAR 4-25, size dependent  |  Where to buy: Wolouf Industries Factory

Anchor Bolt Suppliers in Riyadh - Structural, Wedge and Specialty Anchor Bolts

• •Steel Corner Trading Est, Muhammad Omar Al Attas Trading Store, and Bolt Castle Trading EST. are all based in Riyadh, covering wedge anchors, zinc-plated through bolts, and specialty branded anchor bolt types

Fasteners Suppliers In Dammam - Anchor Bolts, Stainless Steel Grades and Foundation Bolts

• •Wolouf Industries Factory, Metal Fasteners Mfr. Co. Ltd, and Brooq Al Amaan Trading are all based in Dammam, giving Eastern Province and industrial-sector buyers direct access to through bolts, stainless/duplex/Hastelloy grades, and L/J type foundation bolts

Anchor Bolts Manufacturer in Saudi Arabia - Industrial Fasteners Including Bolts, Washers, Nuts, Screws and Anchor Bolts

• •Beyond anchor bolts specifically, most of these suppliers also stock the wider industrial fastener range - hex bolts, washers, nuts, and screws - covering a full site's fixing needs from one procurement source