0 
Busbar Suppliers in KSA | Copper Busbars & Rods, Flexible Cu Busbar and Aluminium Bus Bar Manufacturers in Saudi Arabia
Looking to buy busbar in Saudi Arabia? This guide connects you with Busbar Suppliers in KSA offering bare and tin-coated copper flat bar from 10 mm to 160 mm, aluminium flat bar from 10 mm to 120 mm, insulated busbar chambers rated 30 A to 400 A, comb bars, crane conductor rail systems and flexible copper braids, all built for low-voltage distribution panels, switchboards and control gear. Whether you need a Copper Busbars Manufacturer & Supplier in Saudi Arabia for a switchgear build, a Busbar Manufacturers in Saudi Arabia shortlist for a factory order, or a single Electrical copper bus bar for one panel, the profiles below cover brands including ALFANAR, SCHNEIDER ELECTRIC, ABB and SOCOMEC.
Browse copper busbar and Aluminium bus bar flat stock alongside Flexible Cu Busbar braids, insulated busbar chambers rated to IP54 and NEMA-3R, and comb bar systems for modular circuit breaker connections — then compare specifications, features, supplier contact details and delivery options across Riyadh and Dammam. If you're searching for Copper Bus Bar Suppliers in Saudi Arabia, comparing Copper Flexible Bus bars In Saudi Arabia against rigid bar, or looking for a switchgear busbar or flexible aluminum busbar suppliers in ksa, the suppliers listed below cover both the Central and Eastern regions with delivery available nationwide.
Buy Busbar in Saudi Arabia
Before Choosing a Busbar
✓ Conductor Material: Copper carries roughly 60% more current than aluminium for the same cross section and terminates more reliably, which is why it dominates switchgear and control panels; aluminium is lighter and lower cost, which suits long high-current distribution runs where weight and budget matter more than compactness.
✓ Bar Width & Thickness: Flat bar on this page runs from 10 mm up to 160 mm wide in copper and up to 120 mm in aluminium — size the cross section to the continuous current, then check it against the short-circuit withstand and the mounting centres, not just the ampacity table.
✓ Bare vs Tin-Coated: Bare copper flat bar to ASTM B187 is the standard for enclosed indoor panels; tin-coated copper to ASTM B187 and B545 resists oxidation at joints and in humid or coastal environments, which matters across much of the Kingdom's Eastern and Western regions.
✓ Rigid vs Flexible: Rigid flat bar carries the main distribution run; flexible copper braids and laminated flexible bars handle the connections between the distribution busbar and the devices inside a panel, where they absorb vibration and allow forming around obstacles in confined spaces.
✓ Rated Voltage & Current: Published ratings here run to 600 VAC on busbar chambers and comb bars, and 1000/1500 V AC/DC on SOCOMEC flexible connections, with current ratings from 32 A comb bars up to 400 A chambers and several thousand amperes on larger trunking systems — confirm both figures against the assembly's design.
✓ Temperature Derating: Ampacity falls as ambient temperature rises — the SOCOMEC flexible bar on this page is rated 113 A at 40°C, 129 A at 50°C and 143 A at 60°C, which shows how much the published figure depends on the stated reference temperature. Always match the rating to the actual enclosure temperature.
✓ Enclosure & Protection: Busbar chambers are supplied to IP54 / NEMA-3R for general indoor and sheltered outdoor use, and IP65 where full weatherproofing is needed — IEC 60529 governs the ingress classification, so quote the IP code rather than describing the enclosure in words.
✓ Application: Electrical Distribution Panels & Switchboards, Low Voltage Power Distribution Systems, Industrial Control Panels & Switchgear, Commercial Building Electrical Distribution, Data Centre Power Distribution, Motor Control Centres, Modular Circuit Breaker Connections, Transformer & Switchgear Connections.
✓ Benefits: Higher Current Density Than Cable in the Same Space • Simpler, Repeatable Bolted Connections • Comb Bar Designs That Eliminate Loose Interconnect Wiring • Flexible Braids That Absorb Vibration and Thermal Movement • IEC 61439 and ASTM-Compliant Constructions for Project Approval
✓ Buyer's Tip: Fix the material and cross section first — matched to continuous current and short-circuit withstand — then decide rigid or flexible for each section of the run, and finally confirm the finish and enclosure rating for the environment; this avoids ordering bare copper for a humid coastal panel, or rigid bar where the connection actually needed a formable flexible braid.
Buy Copper Flat Bar, Aluminium Bus Bar, Busbar Chambers & Flexible Braids
Match Your Need to the Right Busbar — Before You Read Anything Else
| If You Need… | You Need a… | Available From |
|---|---|---|
| An enclosed busbar chamber for a 100 A distribution board | ALFANAR Busbar Chamber 30-100A Type 3P | Noor Al Misaq Trading EST – +966 50 072 4875 |
| A higher-rated chamber for a 300–400 A main distribution board | Alfanar Busbar Chamber 300 400A Type 3P MCCB 400AF | Noor Al Misaq Trading EST – +966 50 072 4875 |
| Bare or tin-coated copper flat bar cut to a panel build | Bare / Tin Coated Copper Flat Bar 10 To 160 mm | United Electrical Supplies Factory Company – +966 11 449 3249 |
| Aluminium flat bar for a lighter high-current run | Aluminium Flat Bar 10 To 120 mm, ASTM B236 | United Electrical Supplies Factory Company – +966 11 449 3249 |
| A flexible connection between busbar and panel devices | SOCOMEC Insulated Copper Braids Busbar 8 × 12 mm | Electric Charge Company – +966 58 220 2331 |
| A comb bar to replace loose interconnect wiring on breakers | SCHNEIDER ELECTRIC GV2G354 Copper Comb Bars 63 A | Adwaa Al Jazeerah Trading EST – +966 55 644 4391 |
| A conductor rail system for an overhead crane | 100 A 3 Phase Insulated Conductor Crane Bus Bar System | Trinity Arabia Equipment Co – +971 50 912 3175 |
| A compact branded busbar for a control panel connection | ABB SRN100 Busbar 32 A 600 V | Adwaa Al Jazeerah Trading EST – +966 55 644 4391 |
Busbar Suppliers in KSA – Riyadh & Dammam Suppliers
Noor Al Misaq Trading EST — ALFANAR Busbar Chamber Supplier in Riyadh
RIYADH · Prince Fahad Ibn Ibrahim Al Saud Street, Al Malaz · Electrical trading establishment · ALFANAR busbar chamber & MCCB busbar stockist
Phone: +966 50 072 4875 | Address: Prince Fahad Ibn Ibrahim Al Saud Street, Al Malaz, Riyadh, KSA
Busbar Products They Offer
- ALFANAR Busbar Chamber 30-100A Type 3P — Brand: ALFANAR | Voltage: 600 VAC | Standard: IEC & NEMA | Frequency: 50/60 Hz | Rated Current: 30–100 A | Main Breaker Type: 3P MCCB100AF | Degree of Protection: IP54 / NEMA-3R — a ready-built three-phase chamber for small and mid-size distribution boards.
- Alfanar Busbar Chamber 300 400A Type 3P MCCB 400AF — Brand: ALFANAR | Voltage: 600 V AC | Standard: IEC & NEMA | Frequency: 50/60 Hz | Rated Current: 300–400 A | Main Breaker Type: 3P MCCB 400AF | Degree of Protection: IP54 / NEMA-3R — the higher-rated chamber in the same family, for main distribution boards.
- Mccb 100 A Busbar Type Alfanar — Brand: ALFANAR | Rated Current: 100 A — Not stated by manufacturer for enclosure rating and dimensions; an MCCB-type busbar arrangement for board connections.
- Bus Bar Chamber — Model: 100A | Colour: Grey, Beige | Mounting: Surface — IP65-rated for weatherproof outdoor performance, three-phase compatible, with main breaker options from 100 A, 150 A, 200 A, 250 A, 300 A or 400 A to match the load.
Price Range
SAR 450–1,200 / unit for the 30–100 A ALFANAR chamber range | SAR 1,800–4,500 / unit for the 300–400 A chamber | SAR 600–2,800 / unit for the IP65 Bus Bar Chamber, depending on main breaker rating
Why Choose Noor Al Misaq Trading EST
- Chamber Specialism: The deepest published busbar chamber range on this page, spanning 30 A up to 400 A with matched MCCB main breakers.
- Dual Standard: Its ALFANAR chambers are built to both IEC and NEMA, with IP54 / NEMA-3R protection, which simplifies approval on mixed-standard projects.
- Outdoor Option: The IP65 Bus Bar Chamber covers weather-exposed positions that an IP54 unit could not.
- Coverage Area: Based on Prince Fahad Ibn Ibrahim Al Saud Street in Al Malaz, Riyadh.
- Contact: Direct mobile order line — +966 50 072 4875.
- Industries Served: Distribution Board Fit-Out, Commercial Buildings, Facilities Maintenance.
- Note: The strongest first call on this page for a ready-built enclosed busbar chamber rather than loose bar stock.
Trinity Arabia Equipment Co — Crane Conductor Rail & Busbar System Supplier in Dammam
DAMMAM · Al Badiyah District, Street No. 4 · Equipment specialist · Crane bus bar systems & conductor rail accessory stockist
Phone: +971 50 912 3175 | Mobile: +971 55 488 5451 | Address: Office No 203, Near Nissan Petromin Showroom, Beside Mini Mart Building No. 6564, Street No. 4, Al Badiyah Dist., Dammam 32243, KSA
Busbar Products They Offer
- 100 A 3 Phase Insulated Conductor Crane Bus Bar System — Type: Crane Bus Bar System | Phase: 3 Phase | Rated Current: 100 A | Conductor Type: High-Conductivity Copper | Insulation Type: High-Quality Insulated Housing — a complete insulated conductor rail run for overhead travelling cranes and hoists.
- End Feeding Joint For Conductor Rail — used to connect the incoming power supply cable to the conductor rail system at the end of the rail, providing a secure electrical connection and reliable distribution along the entire rail.
- Bolted Joint For Conductor Rail — used to securely connect two sections of conductor rail, ensuring proper mechanical alignment and continuous electrical conductivity throughout the system for safe power transmission.
- Sliding Hanger For Conductor Rail — supports the conductor rail while allowing controlled movement to accommodate thermal expansion and contraction, maintaining alignment for smooth, reliable operation.
Price Range
SAR 180–450 / metre for the 100 A insulated crane conductor rail | SAR 120–400 / piece for end feeding and bolted joints | SAR 45–140 / piece for sliding hangers, depending on rail profile
Why Choose Trinity Arabia Equipment Co
- Complete System: The only supplier on this page carrying the conductor rail plus its feeding joints, bolted joints and sliding hangers — so the whole run comes from one source and the parts actually fit together.
- Location Fit: The only supplier based in the Eastern Province, serving Dammam, Al Khobar and Jubail industrial sites directly.
- Thermal Allowance: Its sliding hanger design accounts for expansion and contraction, which is what usually fails first on a long rail run in Saudi ambient conditions.
- Coverage Area: Based in the Al Badiyah district of Dammam 32243.
- Contact: Two direct mobile order lines — +971 50 912 3175 / +971 55 488 5451.
- Industries Served: Overhead Cranes & Hoists, Heavy Material Handling, Eastern Province Industrial Facilities.
- Note: The strongest first call for a moving-load conductor rail rather than a fixed panel busbar.
Adwaa Al Jazeerah Trading EST — SCHNEIDER ELECTRIC & ABB Comb Bar Supplier in Riyadh
RIYADH · Asad Ibn Al Fourat, Al Amal · Electrical trading establishment · SCHNEIDER ELECTRIC & ABB branded busbar stockist
Phone: +966 55 644 4391 | Address: Asad Ibn Al Fourat, Al Amal, Riyadh, KSA
Busbar Products They Offer
- SCHNEIDER ELECTRIC GV2G354 Copper Comb Bars 63 A — Brand: SCHNEIDER ELECTRIC | Model: GV2G354 | Length: 54 mm | System: Linergy FT | Material: Copper | Maximum Current: 63 A — the comb design improves power distribution by reducing the need for additional wires, installs quickly to cut working time, and suits distribution panels and industrial control systems needing reliable, repeatable connections.
- ABB SRN100 Busbar 32 A 600 V — Brand: ABB | Model Number: SRN100 | Current: 32 A | Voltage: 600 VAC | Weight: 0.5 kg — designed for efficient electrical conduction in industrial and commercial applications, providing reliable connections for power distribution within electrical panels and systems.
- Supply Busbar, Fork Type Electric Connection, 12 Pole — Width: 17.7 mm | Length: 214 mm | Number Of Pole: 12 | Type Of Electric Connection: Fork — a twelve-pole supply busbar for modular circuit breaker rows in a distribution board.
Price Range
SAR 90–280 / piece for the SCHNEIDER ELECTRIC GV2G354 comb bar | SAR 60–180 / piece for the ABB SRN100 | SAR 45–150 / piece for the 12-pole fork-type supply busbar
Why Choose Adwaa Al Jazeerah Trading EST
- Brand Access: The only supplier on this page carrying both SCHNEIDER ELECTRIC and ABB branded busbar products, which matters when a specification names the manufacturer.
- Installation Speed: Comb bars and fork-type supply busbars remove most of the loose interconnect wiring from a breaker row, cutting build time and inspection findings.
- Panel-Builder Fit: Its range targets the inside of the board rather than the incoming distribution, which suits assembly workshops.
- Coverage Area: Based at Asad Ibn Al Fourat in Al Amal, Riyadh.
- Contact: Direct mobile order line — +966 55 644 4391.
- Industries Served: Panel Building, Industrial Control Systems, Modular Distribution Boards.
- Note: A strong first call for branded comb bars and modular circuit breaker connections rather than cut-to-length bar stock.
United Electrical Supplies Factory Company — Copper & Aluminium Flat Bar Manufacturer in Riyadh
RIYADH · Al Kharj Road, New Industrial Area · Factory & manufacturer · Bare, tin-coated copper & aluminium flat bar producer
Phone: +966 11 449 3249 | Address: Al Kharj Road, New Industrial Area, Riyadh, KSA
Busbar Products They Offer
- Bare Copper Flat Bar 10 To 160 mm — Type: Copper Bus Bar | Width: 10–160 mm | Standard: ASTM B187 — the standard Electrical copper bus bar stock for enclosed switchgear and distribution panels.
- Tin Coated Copper Flat Bar 10 To 160 mm — Type: Copper Bus Bar | Width: 10–160 mm | Standard: ASTM B187 & B545 — the tin plating resists oxidation at bolted joints, which extends joint life in humid and coastal environments.
- Aluminium Flat Bar 10 To 120 mm — Type: Aluminium Bus Bar | Width: 10–120 mm | Standard: ASTM B236 — a lighter, lower-cost Aluminium bus bar option for high-current distribution where weight matters.
- Busbar 10 To 100 mm — Type: Copper, Aluminium | Width: 10–100 mm | Material: Copper/Alum — a general bar line for distributing power inside panel interiors, available in either material.
Price Range
SAR 120–340 / kg for bare copper flat bar, moving with the copper market | SAR 140–380 / kg for tin-coated copper flat bar | SAR 45–110 / kg for aluminium flat bar
Why Choose United Electrical Supplies Factory Company
- Manufacturer Status: Operates as a factory in the New Industrial Area, which usually means better control over cut lengths, widths and lead times than a pure trading company — the natural fit for a Busbar Manufacturers in Saudi Arabia enquiry.
- Material Choice: The only supplier here offering bare copper, tin-coated copper and aluminium bar from the same source, so you can compare cost against ampacity directly.
- Standards: Publishes ASTM B187, B545 and B236 against its bar stock, which is what a switchboard inspector will ask for.
- Coverage Area: Based on Al Kharj Road, New Industrial Area, Riyadh.
- Contact: Single landline order line — +966 11 449 3249.
- Industries Served: Switchgear Manufacturing, Panel Building, Transformer & Substation Connections.
- Note: The strongest first call on this page for raw copper or aluminium bar stock by width and weight.
Electric Charge Company — SOCOMEC Flexible Cu Busbar & Copper Braid Supplier in Riyadh
RIYADH · Prince Abdul Muhsin Bin Abdulaziz Road, Al Malaz · Electrical supplies company · SOCOMEC flexible copper braid & laminated bar stockist
Phone: +966 58 220 2331 | Address: Prince Abdul Muhsin Bin Abdulaziz Road, Al Malaz, Riyadh, KSA
Busbar Products They Offer
- Insulated Copper Braids Busbar 8 × 12 mm (Reference 45161620) — Brand: SOCOMEC | Dimension: 8 × 12 mm | Cross Section: 25 mm² | Length: 220 mm | Distance: 200 mm | Width: 20, 22 mm | Diameter: 8.5, 10.5 mm | Thickness: 1.5, 3.5 mm | Contact Surface: Bare Copper | Dielectric Strength: 20 kV/mm | Operating Temperature: −40 to +105°C | Operating Voltage AC/DC: 1000, 1500 V — used to provide power connections between distribution busbars and the devices within an electrical panel, with flexibility suited to complex connections in confined spaces.
- Insulated Flexible Copper Bars Busbar 9 × 2 × 0.8 mm (Reference 45180902) — Brand: SOCOMEC | Length: 2000 mm | Dimension: 9 × 2 × 0.8 mm | Permissible Amperage: 113 A at 40°C, 129 A at 50°C, 143 A at 60°C — provides power connections between busbars and the disconnection devices within a panel; the insulated layered copper can be formed easily to produce a customised solution.
Price Range
SAR 85–260 / piece for the SOCOMEC insulated copper braids, depending on cross section and length | SAR 350–900 / 2000 mm length for the insulated flexible laminated copper bar
Why Choose Electric Charge Company
- Flexible Specialism: The only supplier on this page publishing a dedicated Flexible Cu Busbar range, covering both braided and laminated formats.
- Published Derating: Its flexible bar states permissible amperage at 40°C, 50°C and 60°C, which lets you size honestly against a real enclosure temperature instead of a single headline figure.
- Wide Temperature Window: The braided range operates from −40°C to +105°C at 1000/1500 V AC/DC, covering demanding panel conditions.
- Coverage Area: Based on Prince Abdul Muhsin Bin Abdulaziz Road in Al Malaz, Riyadh.
- Contact: Direct mobile order line — +966 58 220 2331.
- Industries Served: Switchgear & Panel Assembly, Motor Control Centres, Data Centre Power Distribution.
- Note: The strongest first call for a formable connection between a distribution busbar and a breaker, switch or disconnector inside a panel.
Which Busbar Type Do You Actually Need?
Busbars range from a 32 A comb bar inside a control panel to several thousand amperes on a trunking run — match your need to the closest format. Busbar systems are available in copper and aluminium constructions, with busbar trunking systems commonly covered by IEC/EN 61439-1 and 61439-6:
- Copper Busbar: the standard for electrical distribution panels, such as the Bare Copper Flat Bar 10–160 mm to ASTM B187.
- Aluminium Busbar: lighter and lower cost for low voltage power distribution, such as the Aluminium Flat Bar 10–120 mm to ASTM B236.
- Insulated Busbar: for switchboards and distribution systems where live parts must be shrouded, such as the SOCOMEC insulated braids and bars.
- Bare Copper Busbar: for switchgear and control panels where the bar sits inside a sealed enclosure.
- Tin-Coated Copper Busbar: the same flat stock with a plated finish that resists joint oxidation in humid conditions.
- Busbar Trunking System: a prefabricated run for commercial building power distribution, covered by IEC/EN 61439-6.
- Air Insulated Busbar: for industrial power distribution where clearance rather than solid insulation provides separation.
- Single Pole Busbar: for modular circuit breaker connections, such as the ABB SRN100 and comb bar ranges.
- Three Phase Busbar: for low voltage power distribution, such as the ALFANAR Type 3P busbar chambers and the 12-pole fork supply busbar.
- Neutral And Earth Busbar: the terminal bars inside a distribution board that collect neutral and protective conductors.
- Conductor Rail / Crane Busbar: an insulated moving-contact system for cranes and hoists, supplied with feeding joints, bolted joints and sliding hangers.
Busbar Types Comparison Table
| Type | Typical Rating / Size | Best Used For | Available From |
|---|---|---|---|
| Bare Copper Flat Bar | 10–160 mm wide | Switchgear, control panels and transformer connections. | United Electrical Supplies Factory – +966 11 449 3249 |
| Tin-Coated Copper Flat Bar | 10–160 mm wide | Humid, coastal and joint-critical installations. | United Electrical Supplies Factory – +966 11 449 3249 |
| Aluminium Flat Bar | 10–120 mm wide | High-current distribution where weight and cost matter. | United Electrical Supplies Factory – +966 11 449 3249 |
| Insulated Busbar Chamber | 30–400 A, 600 VAC | Distribution boards needing an enclosed, ready-built unit. | Noor Al Misaq Trading EST – +966 50 072 4875 |
| Comb Bar / Single Pole Busbar | 32–63 A | Modular circuit breaker rows and control systems. | Adwaa Al Jazeerah Trading EST – +966 55 644 4391 |
| Flexible Copper Braid / Laminated Bar | 113–143 A, 1000/1500 V | Busbar-to-device connections in confined panel spaces. | Electric Charge Company – +966 58 220 2331 |
| Crane Conductor Rail System | 100 A, 3 Phase | Overhead cranes, hoists and moving loads. | Trinity Arabia Equipment Co – +971 50 912 3175 |
Busbar Standards
| Standard | Application / Requirement |
|---|---|
| IEC 61439-1 | General requirements for low-voltage switchgear and controlgear assemblies |
| IEC 61439-2 | Power switchgear and controlgear assemblies |
| IEC 61439-6 | Busbar trunking systems |
| IEC 60529 | IP protection classification for enclosures |
| IEC 60364-3 | Electrical installation network classification |
| IEC 60947-3 | Switches, disconnectors and switch-disconnectors used with busbar systems |
| VDE 0660 Part 600-1 / 600-6 | Requirements referenced for certain busbar systems |
| ASTM B187 | Copper bus bar, rod and shapes — applied to the bare and tin-coated copper flat bar on this page |
| ASTM B545 | Electrodeposited tin coatings — applied to the tin-coated copper flat bar range |
| ASTM B236 | Aluminium bars for electrical purposes — applied to the aluminium flat bar range |
Siemens specifies IEC/EN 61439-1 and -6 for its busbar trunking systems, while IEC 60529 is used for enclosure ingress protection — the ALFANAR chambers listed above publish IP54 / NEMA-3R under that same classification, and the IP65 Bus Bar Chamber sits a step higher for weather-exposed positions.
Busbar Frequency And Length
| Busbar Specification | Common Range / Value |
|---|---|
| Rated Frequency | 50 Hz / 60 Hz |
| Standard Busbar Trunking Section | Manufacturer-specific |
| Tap-Off Point Spacing | 0.5 m or 1 m on specified Siemens systems |
| Busbar Material | Copper or Aluminium |
| Rated Operating Voltage | Up to 690–1,000 V AC, depending on system; 1000/1500 V AC/DC on SOCOMEC flexible connections |
| Busbar Current Rating | Application-specific; busbar systems are available from low-current modular systems to several thousand amperes |
| Copper Flat Bar Width | 10–160 mm, bare or tin-coated |
| Aluminium Flat Bar Width | 10–120 mm |
| Flexible Bar Operating Temperature | −40 to +105°C on the SOCOMEC insulated copper braid range |
Busbar Brand Comparison
Here are the brands our Busbar Suppliers in KSA offer, from raw flat bar stock to branded comb bars and flexible connections:
| Brand | Busbar / Busbar System | Approx. Price Range | Ask At |
|---|---|---|---|
| ALFANAR | Busbar chambers 30–400 A, Type 3P, IP54 / NEMA-3R | SAR 450–4,500 / unit | Noor Al Misaq Trading EST – +966 50 072 4875 |
| SCHNEIDER ELECTRIC | Linergy FT copper comb bars up to 63 A, busbar trunking and switchboard systems | SAR 90–280 / piece | Adwaa Al Jazeerah Trading EST – +966 55 644 4391 |
| ABB | Low-voltage modular busbar systems, SRN100 32 A 600 V | SAR 60–180 / piece | Adwaa Al Jazeerah Trading EST – +966 55 644 4391 |
| SOCOMEC | Insulated copper braids and laminated flexible copper bars, 1000/1500 V | SAR 85–900 / piece | Electric Charge Company – +966 58 220 2331 |
| Mill Stock (Copper) | Bare and tin-coated copper flat bar, ASTM B187 & B545 | SAR 120–380 / kg | United Electrical Supplies Factory – +966 11 449 3249 |
| Mill Stock (Aluminium) | Aluminium flat bar, ASTM B236 | SAR 45–110 / kg | United Electrical Supplies Factory – +966 11 449 3249 |
| Conductor Rail | 100 A 3-phase insulated crane bus bar system with joints and hangers | SAR 45–450 / m or piece | Trinity Arabia Equipment Co – +971 50 912 3175 |
| Other Brands | Siemens busbar trunking systems, Eaton busbar trunking and power distribution systems, Rittal modular busbar systems and Wöhner low-voltage busbar components are also available on request — contact the suppliers above for current stock and lead time. | ||
Busbar Applications
Match your specific job to the right busbar, each tied to a specific in-stock product:
Busbar For Electrical Distribution Panels And Switchboards
ALFANAR Busbar Chamber 30-100A Type 3P
Voltage: 600 VAC | Rated Current: 30–100 A | Main Breaker: 3P MCCB100AF | Protection: IP54 / NEMA-3R
Function: A ready-built, enclosed three-phase distribution point that drops straight into a board layout.
Available From: Noor Al Misaq Trading EST — +966 50 072 4875
Busbar For Low Voltage Power Distribution Systems
Aluminium Flat Bar 10 To 120 mm
Type: Aluminium Bus Bar | Width: 10–120 mm | Standard: ASTM B236
Function: A lighter, lower-cost conductor for long low-voltage distribution runs where copper would be over-specified on budget.
Available From: United Electrical Supplies Factory Company — +966 11 449 3249
Busbar For Industrial Control Panels And Switchgear
ABB SRN100 Busbar 32 A 600 V
Brand: ABB | Model Number: SRN100 | Current: 32 A | Voltage: 600 VAC | Weight: 0.5 kg
Function: Efficient electrical conduction and reliable connections for power distribution within industrial and commercial panels.
Available From: Adwaa Al Jazeerah Trading EST — +966 55 644 4391
Busbar For Commercial Building Electrical Distribution
Alfanar Busbar Chamber 300 400A Type 3P MCCB 400AF
Voltage: 600 V AC | Rated Current: 300–400 A | Standard: IEC & NEMA | Protection: IP54 / NEMA-3R
Function: Sized for the main distribution board of a commercial building or a large floor-level sub-board.
Available From: Noor Al Misaq Trading EST — +966 50 072 4875
Busbar For Data Center Power Distribution Systems
Insulated Flexible Copper Bars Busbar 9 × 2 × 0.8 mm
Brand: SOCOMEC | Length: 2000 mm | Permissible Amperage: 113 A at 40°C, 129 A at 50°C, 143 A at 60°C
Function: Published amperage at three ambient temperatures makes honest derating possible in the warm, densely packed enclosures typical of data centre power distribution.
Available From: Electric Charge Company — +966 58 220 2331
Busbar For Motor Control Centers And Industrial Equipment
Insulated Copper Braids Busbar 8 × 12 mm
Brand: SOCOMEC | Cross Section: 25 mm² | Dielectric Strength: 20 kV/mm | Operating Temperature: −40 to +105°C
Function: Braided construction absorbs the vibration and thermal movement typical of a motor control centre while keeping the connection intact.
Available From: Electric Charge Company — +966 58 220 2331
Busbar For Modular Circuit Breaker And Distribution Board Connections
Supply Busbar, Fork Type Electric Connection, 12 Pole
Width: 17.7 mm | Length: 214 mm | Number Of Pole: 12 | Type Of Electric Connection: Fork
Function: Feeds a full row of modular breakers from one bar, removing twelve separate interconnect wires from the board.
Available From: Adwaa Al Jazeerah Trading EST — +966 55 644 4391
Copper Busbar For Transformer And Switchgear Connections
Tin Coated Copper Flat Bar 10 To 160 mm
Type: Copper Bus Bar | Width: 10–160 mm | Standard: ASTM B187 & B545
Function: The tin plating protects the bolted joint faces at transformer and switchgear terminations, where joint resistance rise is the usual failure mode.
Available From: United Electrical Supplies Factory Company — +966 11 449 3249
Busbar Trunking For High-Current Building Power Distribution
100 A 3 Phase Insulated Conductor Crane Bus Bar System
Type: Crane Bus Bar System | Phase: 3 Phase | Rated Current: 100 A | Conductor: High-Conductivity Copper
Function: The closest in-stock prefabricated run on this page, supplied with end feeding joints, bolted joints and sliding hangers for a complete installation.
Available From: Trinity Arabia Equipment Co — +971 50 912 3175
Busbar Types & Features
A closer look at specific busbar types and features, matched to a specific in-stock product where one is available:
Copper Busbar For Electrical Distribution Panels
Busbar 10 To 100 mm
Type: Copper, Aluminium | Width: 10–100 mm | Material: Copper/Alum
Feature: Purpose-built to distribute power across panel interiors, available in either material at the same widths for direct cost-versus-ampacity comparison.
Available From: United Electrical Supplies Factory Company — +966 11 449 3249
Bare Copper Busbar For Switchgear And Control Panels
Bare Copper Flat Bar 10 To 160 mm
Type: Copper Bus Bar | Width: 10–160 mm | Standard: ASTM B187
Feature: The widest copper section on this page, suited to the main runs inside switchgear cubicles where the bar is fully enclosed.
Available From: United Electrical Supplies Factory Company — +966 11 449 3249
Insulated Busbar For Electrical Switchboards And Distribution Systems
Insulated Copper Braids Busbar 8 × 12 mm (Ref. 45161620)
Brand: SOCOMEC | Cross Section: 25 mm² | Operating Voltage AC/DC: 1000, 1500 V | Dielectric Strength: 20 kV/mm
Feature: Bare copper contact surfaces with an insulated body, so the connection is shrouded along its length but still bolts down cleanly at each end.
Available From: Electric Charge Company — +966 58 220 2331
Single Pole Busbar For Modular Circuit Breaker Connections
SCHNEIDER ELECTRIC GV2G354 Copper Comb Bars 63 A
Model: GV2G354 | System: Linergy FT | Length: 54 mm | Material: Copper | Maximum Current: 63 A
Feature: A compact, highly durable comb design that cuts working time on installation and improves maintenance access later.
Available From: Adwaa Al Jazeerah Trading EST — +966 55 644 4391
Three Phase Busbar For Low Voltage Power Distribution
Bus Bar Chamber
Model: 100A | Colour: Grey, Beige | Mounting: Surface | Protection: IP65
Feature: Outdoor-ready IP65 weatherproof construction with three-phase compatibility and a choice of 100 A, 150 A, 200 A, 250 A, 300 A or 400 A main breakers.
Available From: Noor Al Misaq Trading EST — +966 50 072 4875
Aluminium Busbar For High-Current Electrical Distribution
Aluminium Flat Bar 10 To 120 mm
Type: Aluminium Bus Bar | Width: 10–120 mm | Standard: ASTM B236
Feature: Roughly a third of the weight of copper for the same volume, which reduces support requirements on long horizontal runs.
Available From: United Electrical Supplies Factory Company — +966 11 449 3249
Air Insulated Busbar For Industrial Power Distribution
Mccb 100 A Busbar Type Alfanar
Brand: ALFANAR | Rated Current: 100 A
Feature: An MCCB-type busbar arrangement for industrial board connections; Not stated by manufacturer for enclosure rating and dimensions, so confirm clearances with the supplier before ordering.
Available From: Noor Al Misaq Trading EST — +966 50 072 4875
Sandwich Busbar Trunking For High-Current Electrical Distribution
Conductor Rail Accessories — End Feeding Joint, Bolted Joint, Sliding Hanger
Function: End feeding joints connect the incoming supply cable to the rail; bolted joints connect two rail sections with proper mechanical alignment and continuous conductivity; sliding hangers support the rail while allowing controlled thermal movement.
Feature: Together these are the jointing and support set a prefabricated high-current run needs — a true sandwich busbar trunking system is not itemised in this catalogue and is available on request.
Available From: Trinity Arabia Equipment Co — +971 55 488 5451
Frequently Asked Questions
Who are the main Busbar Suppliers in KSA?
The Busbar Suppliers in KSA covered here are Noor Al Misaq Trading EST for ALFANAR busbar chambers, Trinity Arabia Equipment Co in Dammam for crane conductor rail systems, Adwaa Al Jazeerah Trading EST for SCHNEIDER ELECTRIC and ABB comb bars, United Electrical Supplies Factory Company for copper and aluminium flat bar, and Electric Charge Company for SOCOMEC flexible copper braids and laminated bars.
Which is the best Copper Busbars Manufacturer & Supplier in Saudi Arabia on this page?
United Electrical Supplies Factory Company is the only supplier here operating as a factory, producing bare copper flat bar to ASTM B187, tin-coated copper to ASTM B187 and B545, and aluminium to ASTM B236 in widths from 10 mm up to 160 mm — which makes it the natural first call for a Busbar Manufacturers in Saudi Arabia or bulk copper busbar enquiry.
Do these suppliers stock Copper Busbars & Rods?
Copper busbar in flat bar form is stocked from 10 mm to 160 mm wide by United Electrical Supplies Factory Company. Round copper rod is not itemised separately in this catalogue, although ASTM B187 — the standard its flat bar is produced to — also covers copper bus bar, rod and shapes, so contact the factory directly to confirm whether rod is produced on the same line.
Where can I get Flexible Cu Busbar or Copper Flexible Bus bars In Saudi Arabia?
Electric Charge Company in Riyadh stocks both SOCOMEC formats: insulated copper braids at 8 × 12 mm with a 25 mm² cross section, rated 1000/1500 V AC/DC and −40 to +105°C, and insulated laminated flexible copper bars at 9 × 2 × 0.8 mm in 2000 mm lengths, rated 113 A at 40°C rising to 143 A at 60°C.
Are there flexible aluminum busbar suppliers in ksa among these companies?
The flexible ranges itemised in this catalogue are copper only — the SOCOMEC braids and laminated bars from Electric Charge Company. Aluminium here is supplied as rigid flat bar from 10 mm to 120 mm by United Electrical Supplies Factory Company. If a flexible aluminium connection is specifically required, contact either supplier directly, since neither publishes that combination in the ranges listed.
What is the difference between copper busbar and Aluminium bus bar?
Copper carries substantially more current for the same cross section and makes more stable bolted joints, so it dominates switchgear busbar and control panel work. Aluminium is roughly a third of the weight and notably cheaper per kilogram, so it suits long high-current distribution runs where the extra cross section can be accommodated — the trade-off is size, joint preparation and creep, not reliability when correctly specified.
Should I use bare or tin-coated Electrical copper bus bar?
Bare copper flat bar to ASTM B187 is fine inside a sealed indoor panel. Tin-coated bar to ASTM B187 and B545 is the better choice where humidity, salt air or frequent thermal cycling would otherwise oxidise the bolted joint faces and drive up contact resistance — which covers most coastal and outdoor installations in the Kingdom. Both are stocked at 10 mm to 160 mm by United Electrical Supplies Factory Company.
Which standards apply to a switchgear busbar assembly?
IEC 61439-1 sets the general requirements for low-voltage switchgear and controlgear assemblies, IEC 61439-2 covers power switchgear assemblies, and IEC 61439-6 covers busbar trunking systems. IEC 60529 governs the enclosure IP rating, IEC 60364-3 the installation network classification, and IEC 60947-3 the switches and disconnectors used with the busbar. VDE 0660 Part 600-1 and 600-6 are referenced for certain systems, while the bar material itself follows ASTM B187, B545 or B236.
Is busbar trunking available, and what tap-off spacing should I expect?
Prefabricated busbar trunking is not itemised as a stocked product in this catalogue; the closest in-stock prefabricated run is the 100 A three-phase insulated crane conductor rail system from Trinity Arabia Equipment Co. Siemens, Schneider Electric and Eaton trunking systems are available on request. Tap-off point spacing is typically 0.5 m or 1 m on specified Siemens systems, with section lengths manufacturer-specific.
How much does busbar cost in Saudi Arabia?
Copper flat bar runs roughly SAR 120–380 per kg and aluminium roughly SAR 45–110 per kg, both moving with the metal market. Comb bars and compact branded busbars run SAR 45–280 per piece, flexible SOCOMEC connections SAR 85–900, and enclosed ALFANAR busbar chambers SAR 450–4,500 depending on rating. Because copper pricing moves daily, always request a dated formal quote rather than working from an indicative range.
Do these suppliers deliver outside Riyadh and Dammam?
Four of the five suppliers are Riyadh-based and Trinity Arabia Equipment Co covers Dammam and the Eastern Province, so between them the Central and Eastern regions are served directly. All typically deliver to other parts of the Kingdom on request — contact them to confirm freight cost and lead time for Jeddah, Al Khobar, Jubail and other cities.